Askina® DresSil is a sterile tristratified dressing with an adhesive layer of silicone in contact with the wound. Devoid of an adhesive border, it combines the absorption capacity of foam, with the adhesive and atraumatic capacity of silicone in contact with the wound. The special structure of the dressing, which has a slight convexity on all four sides, allows its proper adaptation to the conformation of the wound, preventing any curling of the edges. In the presence of exudate, it also helps keep the environment around the wound moist, promoting the natural conditions for spontaneous healing.

Askina® DresSil is indicated for the treatment of a wide range of exuding lesions, of partial or full thickness, such as:
- Pressure ulcers
- Venous and arterial ulcers of the lower extremities
- Diabetic foot ulcers
- Grade I and II burns
- Exsanguination sites
- Skin lacerations 1) Lesion-contact layer: medical silicone film equipped with a special architecture of holes that allow the passage of exudate to the subsequent polyurethane foam layer. The structure of the holes is characterized by a matrix that is repeated throughout the extent of the silicone layer and consists of a central hole with a diameter of 5 mm surrounded by 6 holes with a diameter of 3 mm.

2) Intermediate layer: hydrophilic absorbent hydrocellular structure consisting of polyurethane foam. It allows high "vertical" absorption of exudate without release under pressure. It also allows excellent management of the wet environment and eliminates the risks of maceration of the wound edges.

3) Outer layer: polyurethane film impermeable to liquids and bacteria and gas permeable. This allows the tissues to breathe, maintaining the proper moist environment while allowing excess fluids to evaporate.

METHOD OF USE.

- Cleanse the wound with a suitable solution (e.g., Prontosan® solution) following normal procedures
- Dry the perilesional skin
- Select a dressing of a suitable size to cover the surface of the lesion, making sure that 2 to 3 cm of dressing remains beyond the margins of the lesion
- Remove the protective sheet and apply the adhesive (silicone) side to the wound
- Adhere the dressing to the wound
- If necessary, secure Askina® DresSil with a secondary dressing
- During removal lift one edge of the dressing and remove it slowly

Askina® DresSil Border is a tri-layered selective microadherence dressing made of polyurethane foam that has, on the side in contact with the wound bed, a layer of silicone equipped with numerous holes that promote the passage of exudate. The special structure of the dressing presents a slight convexity on all four sides, allowing its proper adaptation to the conformation of the wound, preventing any curling of the edges. The presence of the adhesive edge in polyurethane film associated with a medical silicone film equipped with a special architecture of holes that guarantees the characteristics of atraumaticity typical of the silicone interface, ensures maximum protection of the perilesional skin and excellent adhesiveness even in parts of the body subjected to stress. The dressing can be easily removed without the release of residue on the wound bed.

Askina® DresSil Border is indicated for the treatment of a wide range of wounds with medium/high exudate, partial or full thickness, such as: pressure ulcers, venous and arterial ulcers of the lower extremities, diabetic foot ulcers, first- and second-degree burns, explantation sites, and skin tears. Its reduced thickness allows its use on injuries in anatomical areas that require high conformability. 1) Lesion contact layer: medical-grade silicone film equipped with a special architecture of holes that allow the passage of exudate to the subsequent polyurethane foam layer.
The structure of the holes is characterized by a matrix that is repeated throughout the extent of the silicone layer and consists of a central hole of 5 mm diameter surrounded by 6 holes of 3 mm diameter.

2) Intermediate layer: hydrophilic absorbent hydrocellular structure consisting of polyurethane foam. It allows high "vertical" absorption of exudate without release under pressure. It also allows
excellent management of the wet environment and eliminates the risks of maceration of the wound edges.

3) Outer layer: polyurethane film impermeable to liquids and bacteria (external agents) and gas permeable. This allows the tissues to breathe, maintaining the right moist environment while allowing liquids to evaporate
in excess.

Method of use:
- Cleanse the wound with a suitable solution (e.g., Prontosan® solution) following normal procedures
- Dry the perilesional skin
- Select a suitable sized dressing to cover the surface of the lesion, making sure there is adequate space between the adhesive edge and the edges of the lesion
- Remove the protective sheet and apply the adhesive (silicone) side to the lesion
- Adhere the dressing to the wound
- During removal, lift one edge of the dressing and remove it slowly

Askina® DresSil Border is a tri-layered selective microadherence dressing made of polyurethane foam that has, on the side in contact with the wound bed, a layer of silicone equipped with numerous holes that promote the passage of exudate. The special structure of the dressing presents a slight convexity on all four sides, allowing its proper adaptation to the conformation of the wound, preventing any curling of the edges. The presence of the adhesive edge in polyurethane film associated with a medical silicone film equipped with a special architecture of holes that guarantees the characteristics of atraumaticity typical of the silicone interface, ensures maximum protection of the perilesional skin and excellent adhesiveness even in parts of the body subjected to stress. The dressing can be easily removed without the release of residue on the wound bed.

Askina® DresSil Border is indicated for the treatment of a wide range of wounds with medium/high exudate, partial or full thickness, such as: pressure ulcers, venous and arterial ulcers of the lower extremities, diabetic foot ulcers, first- and second-degree burns, explantation sites, and skin tears. Its reduced thickness allows its use on injuries in anatomical areas that require high conformability. 1) Lesion contact layer: medical-grade silicone film equipped with a special architecture of holes that allow the passage of exudate to the subsequent polyurethane foam layer.
The structure of the holes is characterized by a matrix that is repeated throughout the extent of the silicone layer and consists of a central hole of 5 mm diameter surrounded by 6 holes of 3 mm diameter.

2) Intermediate layer: hydrophilic absorbent hydrocellular structure consisting of polyurethane foam. It allows high "vertical" absorption of exudate without release under pressure. It also allows
excellent management of the wet environment and eliminates the risks of maceration of the wound edges.

3) Outer layer: polyurethane film impermeable to liquids and bacteria (external agents) and gas permeable. This allows the tissues to breathe, maintaining the right moist environment while allowing liquids to evaporate
in excess.

Method of use:
- Cleanse the wound with a suitable solution (e.g., Prontosan® solution) following normal procedures
- Dry the perilesional skin
- Select a suitable sized dressing to cover the surface of the lesion, making sure there is adequate space between the adhesive edge and the edges of the lesion
- Remove the protective sheet and apply the adhesive (silicone) side to the lesion
- Adhere the dressing to the wound
- During removal, lift one edge of the dressing and remove it slowly

Askina® DresSil Border is a tri-layered selective microadherence dressing made of polyurethane foam that has, on the side in contact with the wound bed, a layer of silicone equipped with numerous holes that promote the passage of exudate. The special structure of the dressing presents a slight convexity on all four sides, allowing its proper adaptation to the conformation of the wound, preventing any curling of the edges. The presence of the adhesive edge in polyurethane film associated with a medical silicone film equipped with a special architecture of holes that guarantees the characteristics of atraumaticity typical of the silicone interface, ensures maximum protection of the perilesional skin and excellent adhesiveness even in parts of the body subjected to stress. The dressing can be easily removed without the release of residue on the wound bed.

Askina® DresSil Border is indicated for the treatment of a wide range of wounds with medium/high exudate, partial or full thickness, such as: pressure ulcers, venous and arterial ulcers of the lower extremities, diabetic foot ulcers, first- and second-degree burns, explantation sites, and skin tears. Its reduced thickness allows its use on injuries in anatomical areas that require high conformability. 1) Lesion contact layer: medical-grade silicone film equipped with a special architecture of holes that allow the passage of exudate to the subsequent polyurethane foam layer.
The structure of the holes is characterized by a matrix that is repeated throughout the extent of the silicone layer and consists of a central hole of 5 mm diameter surrounded by 6 holes of 3 mm diameter.

2) Intermediate layer: hydrophilic absorbent hydrocellular structure consisting of polyurethane foam. It allows high "vertical" absorption of exudate without release under pressure. It also allows
excellent management of the wet environment and eliminates the risks of maceration of the wound edges.

3) Outer layer: polyurethane film impermeable to liquids and bacteria (external agents) and gas permeable. This allows the tissues to breathe, maintaining the right moist environment while allowing liquids to evaporate
in excess.

Method of use:
- Cleanse the wound with a suitable solution (e.g., Prontosan® solution) following normal procedures
- Dry the perilesional skin
- Select a suitable sized dressing to cover the surface of the lesion, making sure there is adequate space between the adhesive edge and the edges of the lesion
- Remove the protective sheet and apply the adhesive (silicone) side to the lesion
- Adhere the dressing to the wound
- During removal, lift one edge of the dressing and remove it slowly

Askina® DresSil Border is a tri-layered selective microadherence dressing made of polyurethane foam that has, on the side in contact with the wound bed, a layer of silicone equipped with numerous holes that promote the passage of exudate. The special structure of the dressing presents a slight convexity on all four sides, allowing its proper adaptation to the conformation of the wound, preventing any curling of the edges. The presence of the adhesive edge in polyurethane film associated with a medical silicone film equipped with a special architecture of holes that guarantees the characteristics of atraumaticity typical of the silicone interface, ensures maximum protection of the perilesional skin and excellent adhesiveness even in parts of the body subjected to stress. The dressing can be easily removed without the release of residue on the wound bed.

Askina® DresSil Border is indicated for the treatment of a wide range of wounds with medium/high exudate, partial or full thickness, such as: pressure ulcers, venous and arterial ulcers of the lower extremities, diabetic foot ulcers, first- and second-degree burns, explantation sites, and skin tears. Its reduced thickness allows its use on injuries in anatomical areas that require high conformability. 1) Lesion contact layer: medical-grade silicone film equipped with a special architecture of holes that allow the passage of exudate to the subsequent polyurethane foam layer.
The structure of the holes is characterized by a matrix that is repeated throughout the extent of the silicone layer and consists of a central hole of 5 mm diameter surrounded by 6 holes of 3 mm diameter.

2) Intermediate layer: hydrophilic absorbent hydrocellular structure consisting of polyurethane foam. It allows high "vertical" absorption of exudate without release under pressure. It also allows
excellent management of the wet environment and eliminates the risks of maceration of the wound edges.

3) Outer layer: polyurethane film impermeable to liquids and bacteria (external agents) and gas permeable. This allows the tissues to breathe, maintaining the right moist environment while allowing liquids to evaporate
in excess.

Method of use:
- Cleanse the wound with a suitable solution (e.g., Prontosan® solution) following normal procedures
- Dry the perilesional skin
- Select a suitable sized dressing to cover the surface of the lesion, making sure there is adequate space between the adhesive edge and the edges of the lesion
- Remove the protective sheet and apply the adhesive (silicone) side to the lesion
- Adhere the dressing to the wound
- During removal, lift one edge of the dressing and remove it slowly

Askina® DresSil Border is a tri-layered selective microadherence dressing made of polyurethane foam that has, on the side in contact with the wound bed, a layer of silicone equipped with numerous holes that promote the passage of exudate. The special structure of the dressing presents a slight convexity on all four sides, allowing its proper adaptation to the conformation of the wound, preventing any curling of the edges. The presence of the adhesive edge in polyurethane film associated with a medical silicone film equipped with a special architecture of holes that guarantees the characteristics of atraumaticity typical of the silicone interface, ensures maximum protection of the perilesional skin and excellent adhesiveness even in parts of the body subjected to stress. The dressing can be easily removed without the release of residue on the wound bed.

Askina® DresSil Border is indicated for the treatment of a wide range of wounds with medium/high exudate, partial or full thickness, such as: pressure ulcers, venous and arterial ulcers of the lower extremities, diabetic foot ulcers, first- and second-degree burns, explantation sites, and skin tears. Its reduced thickness allows its use on injuries in anatomical areas that require high conformability. 1) Lesion contact layer: medical-grade silicone film equipped with a special architecture of holes that allow the passage of exudate to the subsequent polyurethane foam layer.
The structure of the holes is characterized by a matrix that is repeated throughout the extent of the silicone layer and consists of a central hole of 5 mm diameter surrounded by 6 holes of 3 mm diameter.

2) Intermediate layer: hydrophilic absorbent hydrocellular structure consisting of polyurethane foam. It allows high "vertical" absorption of exudate without release under pressure. It also allows
excellent management of the wet environment and eliminates the risks of maceration of the wound edges.

3) Outer layer: polyurethane film impermeable to liquids and bacteria (external agents) and gas permeable. This allows the tissues to breathe, maintaining the right moist environment while allowing liquids to evaporate
in excess.

Method of use:
- Cleanse the wound with a suitable solution (e.g., Prontosan® solution) following normal procedures
- Dry the perilesional skin
- Select a suitable sized dressing to cover the surface of the lesion, making sure there is adequate space between the adhesive edge and the edges of the lesion
- Remove the protective sheet and apply the adhesive (silicone) side to the lesion
- Adhere the dressing to the wound
- During removal, lift one edge of the dressing and remove it slowly

Askina® DresSil Border is a tri-layered selective microadherence dressing made of polyurethane foam that has, on the side in contact with the wound bed, a layer of silicone equipped with numerous holes that promote the passage of exudate. The special structure of the dressing presents a slight convexity on all four sides, allowing its proper adaptation to the conformation of the wound, preventing any curling of the edges. The presence of the adhesive edge in polyurethane film associated with a medical silicone film equipped with a special architecture of holes that guarantees the characteristics of atraumaticity typical of the silicone interface, ensures maximum protection of the perilesional skin and excellent adhesiveness even in parts of the body subjected to stress. The dressing can be easily removed without the release of residue on the wound bed.

Askina® DresSil Border is indicated for the treatment of a wide range of wounds with medium/high exudate, partial or full thickness, such as: pressure ulcers, venous and arterial ulcers of the lower extremities, diabetic foot ulcers, first- and second-degree burns, explantation sites, and skin tears. Its reduced thickness allows its use on injuries in anatomical areas that require high conformability. 1) Lesion contact layer: medical-grade silicone film equipped with a special architecture of holes that allow the passage of exudate to the subsequent polyurethane foam layer.
The structure of the holes is characterized by a matrix that is repeated throughout the extent of the silicone layer and consists of a central hole of 5 mm diameter surrounded by 6 holes of 3 mm diameter.

2) Intermediate layer: hydrophilic absorbent hydrocellular structure consisting of polyurethane foam. It allows high "vertical" absorption of exudate without release under pressure. It also allows
excellent management of the wet environment and eliminates the risks of maceration of the wound edges.

3) Outer layer: polyurethane film impermeable to liquids and bacteria (external agents) and gas permeable. This allows the tissues to breathe, maintaining the right moist environment while allowing liquids to evaporate
in excess.

Method of use:
- Cleanse the wound with a suitable solution (e.g., Prontosan® solution) following normal procedures
- Dry the perilesional skin
- Select a suitable sized dressing to cover the surface of the lesion, making sure there is adequate space between the adhesive edge and the edges of the lesion
- Remove the protective sheet and apply the adhesive (silicone) side to the lesion
- Adhere the dressing to the wound
- During removal, lift one edge of the dressing and remove it slowly

Askina® DresSil Sacrum is a selective microadherent, tristratified, polyurethane foam dressing that has, on the side in contact with the wound bed, a layer of silicone fitted with numerous
holes that promote the passage of exudate. The special structure of the dressing allows the correct adaptation of the dressing at the level of the sacral area, preventing the possible curling of the edges and the infiltration of any effluent. The presence of the polyurethane film edge associated with a medical silicone film equipped with a special architecture of holes that guarantees the atraumatic characteristics typical of the silicone interface, ensures maximum protection of the perilesional skin and excellent adhesiveness even in parts of the body subjected to stress.

Intended use:
Askina® DresSil Sacrum is indicated for the treatment of exudating lesions of partial or full thickness, such as: pressure ulcers. 1) Lesion-contact layer: medical silicone film equipped with a special architecture of holes that allow the passage of exudate to the subsequent polyurethane foam layer. The structure of the holes is characterized by a matrix that is repeated throughout the extent of the silicone layer and consists of a central hole with a diameter of 5 mm surrounded by 6 holes with a diameter of 3 mm.

2) Intermediate layer: hydrophilic absorbent hydrocellular structure consisting of polyurethane foam. It allows high "vertical" absorption of exudate without release under pressure. It also allows excellent management of the wet environment and eliminates the risks of maceration of the wound edges.

3) Outer layer: polyurethane film impermeable to liquids and bacteria and gas permeable. This allows the tissues to breathe, maintaining the proper moist environment while allowing excess fluids to evaporate.

Method of use:
- Cleanse the wound with a suitable solution (e.g., Prontosan® solution) following normal procedures
- Dry the perilesional skin
- Remove the protective sheetp and apply the adhesive (silicone) side to the wound
- Adhere the dressing to the wound
- During removal, lift one edge of the dressing and remove it slowly

Askina® DresSil Heel is a selective microadherent, tri-layered, polyurethane foam shaped heel dressing that has, on the side in contact with the wound bed, a layer of silicone fitted with numerous holes that promote the passage of exudate. The special structure of the dressing allows the correct adaptation of the dressing at the level of the sacral area, preventing the possible curling of the edges and the infiltration of any effluent. The presence of the polyurethane film edge associated with a medical silicone film equipped with a special architecture of holes that guarantees the atraumatic characteristics typical of the silicone interface, ensures maximum protection of the perilesional skin and excellent adhesiveness even in parts of the body subjected to stress.

Dimensions:
22cm x 21.6cm --> hydroactive surface area of 433cm2

Indications:
Askina® DresSil Heel is indicated for the treatment of moderately exuding lesions of partial or full thickness. 1) Lesion-contact layer: medical silicone film equipped with a special architecture of holes that allow the passage of exudate to the subsequent polyurethane foam layer. The structure of the holes is characterized by a matrix that is repeated throughout the extent of the silicone layer and consists of a central hole of 5 mm diameter surrounded by 6 holes of 3 mm diameter.

2) Intermediate layer: hydrophilic absorbent hydrocellular structure consisting of polyurethane foam. It allows high "vertical" absorption of exudate without release under pressure. It also allows excellent management of the wet environment and eliminates the risks of maceration of the wound edges.

3) Outer layer: polyurethane film impermeable to liquids and bacteria and gas permeable. This allows the tissues to breathe, maintaining the proper moist environment while allowing excess fluids to evaporate.

Instructions for use:
1) Cleanse the wound with a suitable solution (e.g., Prontosan) following normal procedures.
2) Dry the perilesional skin.
3) Place the dressing making sure that 2 to 3 cm of dressing remains beyond the wound margins
4) Remove one of the protective sheets and apply the adhesive side to the wound
5) Adhere the dressing to the lesion by removing the other protective sheet as shown in the diagram below